#Bathtub overflow drain kit how to#
#Bathtub overflow drain kit install#

The most common type is the drain plug, inserted into the drain hole to block water from flowing out. Bathtub drains come in a variety of shapes and sizes. Sizes and materials of Bath Pop Up Waste Components Contact a local plumber or contractor today to discuss your options. With proper installation, they can provide years of trouble-free use. Bath Waste with Overflow Assembly is an excellent option for any bathroom. If you are planning on remodeling your bathroom or building a new home, be sure to consider the different types of bathtub drains available. By installing a Bath Waste with Overflow Assembly, you can ensure that your bathroom will have proper drainage without taking up too much space. They are especially useful in small bathrooms where space is limited. Finally, floor-mounted drains are installed on the floor of the bathroom and collect water as it flows down.īath Waste with Overflow Assembly can be used in any bathroom design. There are also overflow drains, which allow water to flow out if the plug is not inserted properly. In order to prevent costly repairs from happening anytime soon after purchase let them fix any potential problems before they arise!īathtub drains come in a variety of shapes and sizes. They produce the main product, which is an overflow kit that fits into your bathtub and decreases water pressure when it fills up with anything other thanclub soda or saltwater Commercial Disinfection Plant Installation & Maintenance Service that involve the installation or maintenance work on water treatment plants such as filtration system replacement filters changes likely due to increased demand which may arise out put greater amount than what was expected by company policy because they were not aware about future workloads before starting.Hofen Sanitary factory can provide a variety of services for their customers.

#Bathtub overflow drain kit install#

The following list includes some possible answers: Engineering Services – we design and install plumbing systems in homes, commercial buildings etc. What kinds of services can provide from Hofen Sanitary factory? The main product is a related bathtub drain overflow kit. Install the trim and your done, but if you run into trouble you can ask for help on the forum.The company has been in business for over 15 years and provides a wide range of products to meet all your needs, from bathtubs downspouts to the basin waste.

After the plug is installed let the tub fill up and leak test the overflow.

Leak test the drain outlet for a couple minutes before putting in the plug assembly.

It also goes behind the tub and is drawn in tight to the tub by the screw or screws.

Place the overflow gasket in with the fat side at the bottom.Tighten in the drain using a PO wrench until the plumbers putty squeezes out and its quite difficult to turn.

Put a small bead of plumbers putty around the underside of the chrome drain outlet.

When your ready to put in the drain assembly, place the rubber gasket on top of the shoe elbow underneath the tub.

You can also mark the pipe just above the fittings to ensure they are fully seated when gluing the pieces together.

#Bathtub overflow drain kit how to#

When your satisfied that the shoe and the overflow elbows will match up with the holes in your tub it should be safe to glue them together ( How to glue pipe).

Follow the image above and make sure the Tee fitting is rolling downwards. If they don’t fit you will have to cut a piece to length using the same size and type of pipe.

Fit the new drain and overflow pieces together without using glue to make sure they fit the overflow and drain opening of the tub.

Disconnect and remove the existing drain and overflow using a PO wrench and screwdriver.

Cut the existing drain just below the floor squarely using a hacksaw or pipe cutter if you have one and clean the burrs from inside the pipe.

PO wrench Installing The Drain And Overflow.

You may have to remove sections of the wall behind the tub and the ceiling below it. Installing a drain and overflow is a relatively simple project, however gaining access to it is not usually all that simple. Drain and overflow kits can be purchased in ABS, PVC, and brass. There are several types of pre-assembled drain and overflow kits available but I recommend using the twist and close type, as they are less prone to failure and are ascetically pleasing. Whether your changing your bathtub or have a broken pipe it may be necessary to replace the drain and overflow, also called a waste and overflow.